DIY Home Decorating with Gelli® Prints

Can you answer YES to the following questions? If you do — I
have a FUN project for you!!

  1. Do you have a large and growing stash of Gelli® prints?
  2. Do you like DIY home decorating projects?
  3. Do you want to create an artful environment?
  4. Do you have stairs (or a ‘bare’ area) in your living space?

Yes? Great!! I answered “yes” to these questions, too!

The ‘bare’ spot in my home is a back staircase. It’s straight up,
slightly narrow — and screaming for some ART!

At first, I didn’t have a clear idea for how I wanted to decorate
the space. Hang prints on the empty walls? Then — my vision snapped
into focus! A collage of Gelli® prints covering each of the risers!!! Here’s
the transformation!

Once the idea takes form, and the spark of enthusiasm gets you
fired up — it’s all about figuring out the logistics. There are endless
ways to approach this project. I’ll explain how I went about making my stair
collages. You may come up with a different plan — and that’s great!
There’s no right or wrong way — just what works best for you!

Fun, isn’t it?!!

The first decision is what to use as the substrate for the
collages. To be honest, I was looking for a process that would allow for a
removable installation — just in case! I considered a variety
of materials including primed canvas, stiff non-woven interfacing, wallpaper,
heavyweight kraft paper and a few others. Each seemed like it would work. I
decided to use primed canvas for its sturdiness and flexibility. Turns out,
it’s perfect for the job!

The risers on my staircase measure 34.75 inches wide — by
6.25 inches high (accounting for a small strip of moulding across each). It
helps to make a paper template, and it’s a good idea to check it against each
riser. If your risers aren’t even, you can make a template for each one, if
needed. Then cut your substrate to size — one piece for each riser.

All of the prints selected for this project are from my stash — and
printed on either card stock or bristol. The plan is to cut the prints into
strips, making them easy to arrange and line up next to each other.

I cut up a TON of prints — way more than I needed!

Cutting the prints into strips goes
pretty fast using this Fiskars® 12″ paper trimmer. The little blade zips right through the prints. But
cutting all that heavyweight painted paper dulls the blade after a while. So if
you’re slicing up piles of prints, it’s good to have an extra blade on hand.
The replacement blade drops right into place — easy to swap out.

The next step is deciding on an
appropriate adhesive for gluing the prints to the canvas. Again, there are so
many different adhesives to choose from. I considered gel medium, matte medium,
PVA, decoupage glue and tacky glue — and
each would work for this project. But I went in a different direction and used Aleene’s® Tack-It Over& Over — applied to the
primed side of the canvas.

Here’s why:  It’s a pressure-sensitive liquid adhesive
that’s very sticky when dry — which
means it turns the canvas substrate into a self-adhesive surface. So you simply
lay the printed strips in place on the sticky surface and press — then burnish the whole collage
with a bone folder. No buckling wet papers! No drying time! Easy peasy 🙂 The
adhesive is designed to create a temporary bond for attaching embellishments to
fabric (making them removable) — but
I find its bond between paper and canvas is strong.

NOTE:  I discovered
when a using a thin coat of Aleene’s® Tack-It Over & Over, the papers can be
carefully removed after they’re in place. When I used a heavy coat of the
adhesive, the paper grabbed onto the sticky adhesive and didn’t let go — and
tore when I tried to remove it. It’s worthwhile to do some testing first — especially
if you’ve never worked with this pressure sensitive adhesive before.

Aleene’s® Tack-it Over & Over is a
very sticky adhesive to work with while wet. I wear disposable gloves to keep
it off my hands — and
definitely recommend it. I use a 3 inch wide Colour Shaper to squeegee the glue
onto the substrate. An old credit card, hotel key card, or piece of mat board
would work too. I find scraping the adhesive onto the canvas (instead of
brushing it on) is a fast and easy way to apply an even coat with good
coverage. Also, be sure to work on a disposable table covering. I place a large
piece of heavy kraft paper under each canvas substrate. Remember, this stuff is
super-sticky when dry, so you don’t want it on your work surface!

After the collages are constructed — while they’re still
on the kraft paper — apply a coat of DecoArts® Americana Decou-page Matte for a protective finish and let them dry. These are now nice
sturdy, sealed pieces — ready to install!

Here’s the step-by-step directions for how I created the collages:

  1. Cut prints into strips.
  2. Create a template for the risers.
  3. Cut a piece of primed canvas for each riser.
  4. Apply a layer of Aleene’s® Tack-it Over & Over to the primed side of each substrate with a scraper tool.
  5. Allow the glue to dry completely. It goes on white — dries clear — and is very sticky when dry.
  6. Place cut print pieces on the substrate and press in place. Burnish with a bone folder to create a strong bond. 
  7. Squeegee on a thin coat of DecoArt Americana Decou-Page Matte to seal the collages. Let dry.
  8. Remove collage from disposable kraft paper. Trim the pieces that extend beyond your substrate. 

The last step is installing the collages on the stair risers. My
risers are painted, and I used Glue Dots® Removable Dots. I applied the dots liberally to the back of each canvas — then
firmly pressed each canvas in place against the riser. The collages are holding
up nicely in their vertical space! When I tested the removal — the
glue dots stuck to the paint, not the canvas — but peeled easily
off the paint without any problems. There are various adhesives designed for
hanging posters on painted walls (that are supposed to offer easy removal) that
may be another way to go. You can explore different options — but
test them in an inconspicuous area first.

What a difference! The whole staircase comes to life with
colorful FUN! What a great way to display Gelli® prints!!

And one of the best parts is that I’ve used so much of my Gelli® print stash — it’s time to start printing again!!! More fun!!!

If you don’t have a staircase, look around for an area that could
use a big blast of color. Henry, at Gelli Arts®, creatively mounted some of his
prints over the doorways in the Gelli Arts® office!!! Fabulous!!!

You can always interpret the basic idea here to a large stretched
canvas or panel — and hang
it where it’ll make you happy 🙂 So go ahead and “Gelli® up” your
home!

Remember,
we now have 
Gelli® partners all over the world, so it’s easier than
ever to find a Gelli
® retailer near you!

http://www.gelliarts.com/pages/find-a-retailer

One last thing… if you haven’t joined us on Instagram – please do! And if you’re sharing yourGelli® artwork on Instagram – please be sure to tag us — @gelliarts! Don’t forget to use the hashtags #gelliplate, #gelliprint or #gelli (or all three!!)  — so that way we can find you too!

Instagram



Have Fun and Happy Printing!

Materials Used In Today’s Blog:

Gelli Arts®Printing Plate
Heavyweight
Kraft Paper
Fredrix
Canvas Roll
Fiskars 12″
Portable Trimmer
Aleene’s Tack-it
Over & Over
Ergo Teflon
Floder/Folding Rib
Disposable Gloves
Silicone Wide Firm
Flat Brush: Size 3
DecoArt Americana
Decou-Page Matte
Glue Dots
Removable Dots

16 thoughts on “DIY Home Decorating with Gelli® Prints”

  1. This looks so pretty!! Thanks for the idea. Yes, I do have a small stash of Gelli prints just waiting for me to put them to use!!

  2. Sketching with Dogs

    That is so incredibly cool! I love what you've done with your stairs. I am looking at my gelli plate in a whole new light 🙂
    Lynne

  3. Mary C. Nasser

    So AMAZING! Love the combination of colors and variety of patterns! Your staircase sings!! Thank you, too, for the thorough directions and supply list! This is super unique and creative!!

  4. Love this idea. You have my mind working overtime trying to think where I can do something like this. I love my gelli plates and can't get enough of my gelli time.

  5. WOW, the stairs now look like a sooo COOL piece of modern art in a museum! It is fun, playful and unique. LOVE it! The white framed picture (the 20th pic down) wherein you have them all together would be a fabulous hanging piece, too. Grand decorating ideas! Thanks for sharing them and for the instructions. 😀

  6. Lynda Howells

    I live in a flat ..no stairs … bother. Um l wonder if l could do this to the stairs outside my flat? NOOOOOOOOO comes a sharp response from my husband ….. ! Ha. I think this maybe a "step" too far !!:)

  7. What an amazing fun idea Joan. It looks fabulous and it's a shame I have carpeted stairs!
    Thanks for sharing.
    Fliss xx

  8. Fantastic idea – reminds me of a designer clothing store in Amsterdam who have carpeted each tread of their staircase with a different patterned carpet and have strips of mismatched wallpaper on their walls. Love the idea of doing it over the doorframe too.
    Glenda x

Leave a Reply

%d bloggers like this: